Wrench ClinicGet a quote

Tyres & Wheels: UK Guide to Care, Checks and Fitting (2026)

Tyres & wheels are the only parts of your car that touch the road, so their condition decides how well you grip, steer and stop. This guide covers pressures, size markings, tread, alignment, buying, fitting, small cars and off-road use.

Key points

  • Check tyre pressures cold, using the figures in your owner's book, fuel-cap sticker or door sill, not the number moulded on the tyre.
  • Read the size marking on the sidewall before you buy, because width, aspect ratio and rim diameter must all match your car's requirements.
  • Uneven wear, pulling to one side or an off-centre steering wheel usually points to alignment or tracking, not the tyres themselves.
  • Spacers, wider wheels and taller tyres change how the car drives and reads speed, so get qualified advice before modifying anything.
TermMeaningWhy it matters
Contact patchThe area of each tyre touching the road, roughly the size of the palm of a hand.Four palm-sized areas carry all your braking, cornering and acceleration.
Cold pressureTyre pressure measured before driving, or after the car has stood for a few hours.Published pressures are cold figures, so warm readings mislead you.
Aspect ratioSidewall height shown as a percentage of the tyre width.It changes ride comfort, steering feel and overall tyre diameter.
Bead seatThe ledge on each side of the rim where the tyre bead rests.Air pressure pushes the bead into it to make an airtight seal.
Wheel alignmentThe angles of the wheels relative to each other and the road.Poor alignment wears tyres unevenly and can pull the car to one side.
TrackingThe direction the wheels point relative to the car's centreline.It is the most commonly adjusted alignment setting.

Tyres & wheels for pressure checks

Correct pressure is the cheapest way to protect your tyres and keep the car stable.

  1. Find your pressures in the owner's book, on the fuel-cap sticker or inside the door sills, never from the number moulded on the sidewall.
  2. Check pressures when the tyres are cold, ideally before the first drive of the day, because warm tyres read higher than the stated figure.
  3. Use a reliable gauge rather than a worn forecourt line, and compare it against a second gauge if two readings differ noticeably.
  4. Adjust pressures for heavy loads or towing only if your handbook gives a separate figure, and write both figures on a note in the glovebox.
  5. Replace missing valve caps straight away, because the cap keeps dirt and moisture out of the valve core.
  6. Check the spare or the repair kit sealant date at the same time, so a puncture does not leave you without a working option.

Our guide on when tyre pressure should be checked sets out a simple routine.

Tyres & wheels size markings

A typical sidewall marking tells you everything a tyre shop needs to match your car.

Part of markingWhat it tells you
WidthTyre width in millimetres, measured across the tread.
Aspect ratioSidewall height as a percentage of the width.
Construction (R)Radial construction, used on almost all modern car tyres.
Rim diameterThe wheel diameter the tyre fits, in inches.
Load indexA code for the maximum load the tyre can carry.
Speed ratingA letter code for the maximum speed the tyre is built for.

Tyres & wheels for tread and wear

Tread shows you what the car is doing long before a tyre fails.

  1. Measure tread depth with a gauge at several points across each tyre, and record the lowest reading so you can track the rate of wear.
  2. Check the current legal minimum tread depth on GOV.UK, and plan to replace tyres well before they reach that limit.
  3. Look for wear on only the inner or outer edge, which usually means alignment or suspension problems rather than a faulty tyre.
  4. Run a hand across the tread, both directions, to feel feathering or saw-tooth edges that point to worn suspension parts or tracking faults.
  5. Inspect sidewalls for cuts, bulges and cracking on all four tyres, and replace any tyre with a bulge, whatever its tread depth.
  6. Rotate tyres only if your handbook recommends it, and always keep the tyres with the most tread on the axle your tyre fitter advises.

Tyres & wheels alignment and tracking

Alignment sets the wheel angles, and tracking is the setting most often corrected.

  1. Suspect alignment if the car pulls to one side on a flat, straight road with your hands lightly on the steering wheel.
  2. Notice a steering wheel that sits off-centre while the car travels straight, because that is a classic sign of a tracking fault.
  3. Book an alignment check after hitting a deep pothole or kerb, even when you cannot see any damage to the wheel.
  4. Have alignment checked whenever you fit new tyres or replace steering and suspension parts, so the new rubber does not wear unevenly.
  5. Ask for a printout of before and after readings, which lets you confirm the work was done and keep a record.
  6. Expect a worn suspension part to be flagged first, since alignment cannot hold if a bush or joint has play.

Drivers in the UK can expect to pay around £80-90 to have their front and rear tyres realigned.

For a front wheel alignment only, the average price is £49.03.

Read more on wheel tracking and wheel alignment cost in the UK.

Tyres & wheels for small cars

Small cars often have low-profile tyres and tight pressure tolerances, so details matter more.

  1. Look up your exact pressures for the model, wheel size and load on the door-sill label, because figures vary between versions.
  2. Check the tyre size on the sidewall before ordering, since small hatchbacks may be offered with several rim diameters.
  3. Take extra care with low-profile tyres on potholed roads, because a short sidewall gives less protection to the wheel rim.
  4. Inspect alloy wheels for kerb scrapes and bends, and have any wheel that loses pressure overnight checked at the bead seat.
  5. Check run-flat or reinforced tyres are replaced with the same type, because mixing types can change handling and warning-system behaviour.
  6. Keep a pressure gauge in the car, since small tyres hold little air and can drop quickly from a slow leak.

Our page on Cooper tyre pressure covers the checks in more detail.

Tyres & wheels for buying and fitting

A good deal depends on matching the right tyre to the car, not only on the headline price.

  1. Compare offers for the same size, load index and speed rating, so you are pricing identical tyres and not different specifications.
  2. Ask whether the quote includes fitting, valves, balancing and disposal of old tyres, since extras can change the total.
  3. Ideally replace tyres in pairs on the same axle, and ask your fitter which axle should take the newer pair.
  4. Check the date code on the sidewall before fitting, and decline any tyre that has been in storage far longer than you expected.
  5. Consider a mobile fitter if you cannot leave the car, but make sure they can balance wheels and torque the nuts correctly.
  6. Re-check wheel nut tightness after the first short drive if your fitter advises it, and keep the locking wheel nut key safe.

See car tyre offers and mobile tyres before you book.

Tyres & wheels for off-road use

Rougher tracks, mud and gravel call for different tyres, but the choice affects road manners too.

  1. Choose an all-terrain tyre when you split time between road and track, accepting some extra road noise and a firmer ride.
  2. Keep the new tyre within about 3% of the factory height and width on an unmodified suspension, to avoid rubbing.
  3. Remember a taller tyre makes the speedometer read lower than your real speed, because it is calibrated to the factory circumference. Check with your fitter that the new size is acceptable for your car.
  4. Carry a puncture kit, a pressure gauge and a compressor, and restore road pressures before rejoining the tarmac.
  5. Check sidewalls after every trip for cuts and embedded flints, because off-road damage often shows there first.
  6. Confirm the load index covers the weight of your car with passengers, roof boxes and equipment on board.

Our guide to all-terrain tyres explains the trade-offs in full.

Tyres & wheels with spacers and modified wheels

Wheel changes alter clearances and loads, so each change needs to be checked by a qualified fitter.

  1. Understand that spacers push the wheel outwards, which changes the load on the wheel bearings and the way the car steers.
  2. Ask a qualified mechanic whether spacers suit your car at all, and use only parts made for your hub and stud pattern.
  3. Check that wider wheels clear the arch liners and suspension through full steering lock and over bumps before you drive away.
  4. Have wheel nuts or bolts torqued to the manufacturer's setting with a calibrated wrench, and re-check them after a short drive.
  5. Tell your insurer about any wheel modification, and keep invoices showing the parts fitted and who fitted them.
  6. Book an alignment check after changing offset or fitting spacers, as wheel position changes how the tyres meet the road.

Learn more about wheel spacers before you buy any.

Tyres & wheels best practices

Related guides

Frequently asked questions

How often should I check my tyre pressures?

Check them at least once a month and before any long trip. Do it when the tyres are cold, because the pressures in your handbook are cold figures, and top up to the stated number for your load.

Where do I find the correct tyre pressure for my car?

Look in the owner's book, on the sticker inside the fuel cap or on the door sills. The number moulded on the tyre is a maximum for the tyre, not the pressure your car needs.

What does the size marking on a tyre mean?

The first number is the width in millimetres and the second is the sidewall height as a percentage of that width. R means radial construction, and the next number is the rim diameter in inches that the tyre fits.

What is the legal minimum tread depth?

The legal limit is set by law and can change, so check the current figure on GOV.UK. Tyres perform worse as they wear, so many drivers replace them well before reaching the limit.

Do I need an alignment after fitting new tyres?

It is wise to have alignment checked when you fit new tyres, particularly if the old ones wore unevenly. Correct settings protect new rubber, and the check shows whether suspension parts need attention.

Are wheel spacers safe to fit?

They are only suitable if they fit your car and are installed correctly by a qualified person. They change loads on bearings and clearances, so get advice from a mechanic first.

Get your tyres & wheels checked

If you are unsure about wear, pressures, alignment or fitting, a mechanic can inspect the car and explain what needs doing. At Wrench Clinic we can send a licensed mechanic to your home or workplace, so ask for a quote and describe what you have noticed.

Get a quote

Request a quote

Tell us what you need and we will get back to you.